Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Gallery Index & Tech Ref
Goldwing Trivia
Goldwing- The First 20 Years
From Japan to USA
Goldwing Magazine Articles
Two Wheel Magazine 1975- Honda's GL1000, The Future
Cycle Illustrated, Nov. 1975- 2 Big Ones From Honda
1977 Model GL1000 Setup Instructions
Owners Manuals
GL1000
1975 GL1000
1978 GL1000
GL1100
1980 GL1100 Standard
1981 GL1100 Interstate
1982 GL1100 Aspencade
1982 GL1100 Interstate
1982 GL1100 Standard
1983 GL1100 Aspencade
1983 GL1100 Interstate
GL1200
1984 GL1200 Standard
1986 GL1200 Interstate
1987 GL1200 Aspencade
GL1500
1987 GL1200 Aspencade
Service Bulletins and Recalls- All Models
GL1000
GL1000- Important GL1000 Service Reminder (1 Page) 6-13-1975
SL #108 Tire and Wheel Rim Matching Information 6-20-75 (7 pages)
Service Tools Newsletter 7-31-75 (2 pages)
SB 1000 #3 Pressurised Cooling System Tester 10-10-75 (3 pages)
SB 1000 #1 Cylinder Head Core Plug Leakage- Revised 7-9-76 (3 pages)
SL #117 Exhaust Pipe and Muffler Paint Damage 9-30-76 (1 page)
SL #118 Instrument Troubleshooting 10-27-76 (5 pages)
PB 1000-2 Changes to Clutch Components 11-3-76 (1 page)
PB 1000-3 Changes to Right Front Engine Cover 1-5-77 (1 page)
SB 1000 #11 Final Drive Gear Case Cover Change 10-15-77 (1 page)
SB 1000 #12 New Main Bearing Caps 11-23-77 (1 page)
SB 1000 #13 Recall to Replace Rear Brake Pads 3-21-78 (5 pages)
SB 1000 #14 Cylinder Head Bolt Torque Change 11-8-78 (1 page)
GL1200
Special Consumer Report: 1984 and 1985 GW Rear Hub
New media
New comments
Search media
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Classic Goldwing Technical Forums
Lighting & Electrical
Rebuild '82 Standard Wire Harness and Fuse Box
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support Classic Goldwings:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="mcgovern61" data-source="post: 178296" data-attributes="member: 59"><p>As I work through doctor visits and testing, I am also working through the 86 schematics. As I follow each circuit I see why the heavier wire was used. Some of the complaints we have had in the past about adding a relay for the coils or a relay for the horn circuit or even adding a buss bar for either a positive buss or negative buss are addressed in this fuse panel.</p><p></p><p>Honda kinda took care of all of that in this fuse panel. There is a 12 gauge wire coming from the 30 amp fuse to the key switch and there is also another positive wire going to another 30 amp fuse which is always hot. This circuit runs to the lower 3 fuses as an "unswitched" circuit (always hot). The key switch sends each of the sections (On/ACC/Park) back to the fuse panel with individual 14 gauge wires with those wires being bussed on several different circuits in the fuse panel. Big amperage units get their power from the relays.</p><p></p><p>It is going to be cool installing this fuse panel with the relays. It will require a careful review of my current '82 harness and most definitely adding larger wires in my harness to match up some of these circuits. I am under the opinion that in the end it will be a great improvement to the bikes circuits!</p></blockquote><p></p>
[QUOTE="mcgovern61, post: 178296, member: 59"] As I work through doctor visits and testing, I am also working through the 86 schematics. As I follow each circuit I see why the heavier wire was used. Some of the complaints we have had in the past about adding a relay for the coils or a relay for the horn circuit or even adding a buss bar for either a positive buss or negative buss are addressed in this fuse panel. Honda kinda took care of all of that in this fuse panel. There is a 12 gauge wire coming from the 30 amp fuse to the key switch and there is also another positive wire going to another 30 amp fuse which is always hot. This circuit runs to the lower 3 fuses as an "unswitched" circuit (always hot). The key switch sends each of the sections (On/ACC/Park) back to the fuse panel with individual 14 gauge wires with those wires being bussed on several different circuits in the fuse panel. Big amperage units get their power from the relays. It is going to be cool installing this fuse panel with the relays. It will require a careful review of my current '82 harness and most definitely adding larger wires in my harness to match up some of these circuits. I am under the opinion that in the end it will be a great improvement to the bikes circuits! [/QUOTE]
Insert quotes…
Verification
Post reply
Classic Goldwing Technical Forums
Lighting & Electrical
Rebuild '82 Standard Wire Harness and Fuse Box
Top