Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Gallery Index & Tech Ref
Goldwing Trivia
Goldwing- The First 20 Years
From Japan to USA
Goldwing Magazine Articles
Two Wheel Magazine 1975- Honda's GL1000, The Future
Cycle Illustrated, Nov. 1975- 2 Big Ones From Honda
1977 Model GL1000 Setup Instructions
Owners Manuals
GL1000
1975 GL1000
1978 GL1000
GL1100
1980 GL1100 Standard
1981 GL1100 Interstate
1982 GL1100 Aspencade
1982 GL1100 Interstate
1982 GL1100 Standard
1983 GL1100 Aspencade
1983 GL1100 Interstate
GL1200
1984 GL1200 Standard
1986 GL1200 Interstate
1987 GL1200 Aspencade
GL1500
1987 GL1200 Aspencade
Service Bulletins and Recalls- All Models
GL1000
GL1000- Important GL1000 Service Reminder (1 Page) 6-13-1975
SL #108 Tire and Wheel Rim Matching Information 6-20-75 (7 pages)
Service Tools Newsletter 7-31-75 (2 pages)
SB 1000 #3 Pressurised Cooling System Tester 10-10-75 (3 pages)
SB 1000 #1 Cylinder Head Core Plug Leakage- Revised 7-9-76 (3 pages)
SL #117 Exhaust Pipe and Muffler Paint Damage 9-30-76 (1 page)
SL #118 Instrument Troubleshooting 10-27-76 (5 pages)
PB 1000-2 Changes to Clutch Components 11-3-76 (1 page)
PB 1000-3 Changes to Right Front Engine Cover 1-5-77 (1 page)
SB 1000 #11 Final Drive Gear Case Cover Change 10-15-77 (1 page)
SB 1000 #12 New Main Bearing Caps 11-23-77 (1 page)
SB 1000 #13 Recall to Replace Rear Brake Pads 3-21-78 (5 pages)
SB 1000 #14 Cylinder Head Bolt Torque Change 11-8-78 (1 page)
GL1200
Special Consumer Report: 1984 and 1985 GW Rear Hub
New media
New comments
Search media
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Classic Goldwing Technical Forums
Goldwing Customization & Tricks
smoke coming out of ignition module?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support Classic Goldwings:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="backlander" data-source="post: 135051" data-attributes="member: 2035"><p>The ICU case is plastic and has no way to be grounded on it's own when bolted to the frame, therefore the green wire is the only ground for the ICU. I have an 85 Interstate wiring harness dissected on a plywood board with the components like the voltage reg/rectifier and ICU attached to it. [ATTACH=full]10260[/ATTACH] The GL wiring harness is a maze of wires with an unbelievable number of factory splices numbered like the S111 where the ICU ground is spliced into one of two large solid green ground wires that run nearly the whole length of the wiring harness. [ATTACH=full]10261[/ATTACH] This is the inside of an ICU and shows the printed circuit boards, if it smoked it is probably toast unless you have an electonic whiz for a friend who can troubleshoot and replace the components that got fried, on the other hand I have seen circuit boards that fried only the electrical path between components and those can be repaired. [ATTACH=full]10262[/ATTACH] I have seen the ICU's available on Ebay. Good luck !!!</p></blockquote><p></p>
[QUOTE="backlander, post: 135051, member: 2035"] The ICU case is plastic and has no way to be grounded on it's own when bolted to the frame, therefore the green wire is the only ground for the ICU. I have an 85 Interstate wiring harness dissected on a plywood board with the components like the voltage reg/rectifier and ICU attached to it. [ATTACH type="full" alt="WP_20141016_002.jpg"]10260._xfImport[/ATTACH] The GL wiring harness is a maze of wires with an unbelievable number of factory splices numbered like the S111 where the ICU ground is spliced into one of two large solid green ground wires that run nearly the whole length of the wiring harness. [ATTACH type="full" alt="WP_20141017_008.jpg"]10261._xfImport[/ATTACH] This is the inside of an ICU and shows the printed circuit boards, if it smoked it is probably toast unless you have an electonic whiz for a friend who can troubleshoot and replace the components that got fried, on the other hand I have seen circuit boards that fried only the electrical path between components and those can be repaired. [ATTACH type="full" alt="IMG01569-20121206-1407.jpg"]10262._xfImport[/ATTACH] I have seen the ICU's available on Ebay. Good luck !!! [/QUOTE]
Insert quotes…
Verification
Post reply
Classic Goldwing Technical Forums
Goldwing Customization & Tricks
smoke coming out of ignition module?
Top