Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Gallery Index & Tech Ref
Goldwing Trivia
Goldwing- The First 20 Years
From Japan to USA
Goldwing Magazine Articles
Two Wheel Magazine 1975- Honda's GL1000, The Future
Cycle Illustrated, Nov. 1975- 2 Big Ones From Honda
1977 Model GL1000 Setup Instructions
Owners Manuals
GL1000
1975 GL1000
1978 GL1000
GL1100
1980 GL1100 Standard
1981 GL1100 Interstate
1982 GL1100 Aspencade
1982 GL1100 Interstate
1982 GL1100 Standard
1983 GL1100 Aspencade
1983 GL1100 Interstate
GL1200
1984 GL1200 Standard
1986 GL1200 Interstate
1987 GL1200 Aspencade
GL1500
1987 GL1200 Aspencade
Service Bulletins and Recalls- All Models
GL1000
GL1000- Important GL1000 Service Reminder (1 Page) 6-13-1975
SL #108 Tire and Wheel Rim Matching Information 6-20-75 (7 pages)
Service Tools Newsletter 7-31-75 (2 pages)
SB 1000 #3 Pressurised Cooling System Tester 10-10-75 (3 pages)
SB 1000 #1 Cylinder Head Core Plug Leakage- Revised 7-9-76 (3 pages)
SL #117 Exhaust Pipe and Muffler Paint Damage 9-30-76 (1 page)
SL #118 Instrument Troubleshooting 10-27-76 (5 pages)
PB 1000-2 Changes to Clutch Components 11-3-76 (1 page)
PB 1000-3 Changes to Right Front Engine Cover 1-5-77 (1 page)
SB 1000 #11 Final Drive Gear Case Cover Change 10-15-77 (1 page)
SB 1000 #12 New Main Bearing Caps 11-23-77 (1 page)
SB 1000 #13 Recall to Replace Rear Brake Pads 3-21-78 (5 pages)
SB 1000 #14 Cylinder Head Bolt Torque Change 11-8-78 (1 page)
GL1200
Special Consumer Report: 1984 and 1985 GW Rear Hub
New media
New comments
Search media
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Classic Goldwing Technical Forums
Restorations
1982 Motor Removal and Stator Change
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support Classic Goldwings:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="wedoo2" data-source="post: 204215" data-attributes="member: 4569"><p>I hooked up the remaining wiring, one connection between the pulse generator and then tackled the stator wires. This is a blurry picture of the three wires that need to be connected after cutting off the connector that came with the new stator.</p><p></p><p><img src="https://image.ibb.co/kPMa1d/IMG_0729.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p></p><p>I attached the wires together, soldered them and put on the shrink wrap on them.</p><p></p><p><img src="https://image.ibb.co/i6DYnJ/IMG_0730.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p></p><p>Time to start it up. Put in a little gas since I had drained it earlier to remove the petcock (that is leaking and a new one ordered) I had to build up the battery but found out that the maintenance </p><p>tender was not working. Put it on my car charger and got things up into the low 13s. The bike turned over slowly but it did turn over.</p><p></p><p>Then a big mess. Carb one was leaking, a lot. And now I am taking the carbs off again. And there is a lot of gas in the cylinders. If I can get the carbs out, and there is no guarantee of that, I'll be taking them to my guy, Motorcycle Bob, to look at them. Probably a bad float bowl gasket. Should have changed them. And float height. I'll let him deal with it and then take him fishing. Don't think I'll make NASR next week.</p><p></p><p>The Gold Witch always is there.</p></blockquote><p></p>
[QUOTE="wedoo2, post: 204215, member: 4569"] I hooked up the remaining wiring, one connection between the pulse generator and then tackled the stator wires. This is a blurry picture of the three wires that need to be connected after cutting off the connector that came with the new stator. [img]https://image.ibb.co/kPMa1d/IMG_0729.jpg[/img] I attached the wires together, soldered them and put on the shrink wrap on them. [img]https://image.ibb.co/i6DYnJ/IMG_0730.jpg[/img] Time to start it up. Put in a little gas since I had drained it earlier to remove the petcock (that is leaking and a new one ordered) I had to build up the battery but found out that the maintenance tender was not working. Put it on my car charger and got things up into the low 13s. The bike turned over slowly but it did turn over. Then a big mess. Carb one was leaking, a lot. And now I am taking the carbs off again. And there is a lot of gas in the cylinders. If I can get the carbs out, and there is no guarantee of that, I'll be taking them to my guy, Motorcycle Bob, to look at them. Probably a bad float bowl gasket. Should have changed them. And float height. I'll let him deal with it and then take him fishing. Don't think I'll make NASR next week. The Gold Witch always is there. [/QUOTE]
Insert quotes…
Verification
Post reply
Classic Goldwing Technical Forums
Restorations
1982 Motor Removal and Stator Change
Top