Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Gallery Index & Tech Ref
Goldwing Trivia
Goldwing- The First 20 Years
From Japan to USA
Goldwing Magazine Articles
Two Wheel Magazine 1975- Honda's GL1000, The Future
Cycle Illustrated, Nov. 1975- 2 Big Ones From Honda
1977 Model GL1000 Setup Instructions
Owners Manuals
GL1000
1975 GL1000
1978 GL1000
GL1100
1980 GL1100 Standard
1981 GL1100 Interstate
1982 GL1100 Aspencade
1982 GL1100 Interstate
1982 GL1100 Standard
1983 GL1100 Aspencade
1983 GL1100 Interstate
GL1200
1984 GL1200 Standard
1986 GL1200 Interstate
1987 GL1200 Aspencade
GL1500
1987 GL1200 Aspencade
Service Bulletins and Recalls- All Models
GL1000
GL1000- Important GL1000 Service Reminder (1 Page) 6-13-1975
SL #108 Tire and Wheel Rim Matching Information 6-20-75 (7 pages)
Service Tools Newsletter 7-31-75 (2 pages)
SB 1000 #3 Pressurised Cooling System Tester 10-10-75 (3 pages)
SB 1000 #1 Cylinder Head Core Plug Leakage- Revised 7-9-76 (3 pages)
SL #117 Exhaust Pipe and Muffler Paint Damage 9-30-76 (1 page)
SL #118 Instrument Troubleshooting 10-27-76 (5 pages)
PB 1000-2 Changes to Clutch Components 11-3-76 (1 page)
PB 1000-3 Changes to Right Front Engine Cover 1-5-77 (1 page)
SB 1000 #11 Final Drive Gear Case Cover Change 10-15-77 (1 page)
SB 1000 #12 New Main Bearing Caps 11-23-77 (1 page)
SB 1000 #13 Recall to Replace Rear Brake Pads 3-21-78 (5 pages)
SB 1000 #14 Cylinder Head Bolt Torque Change 11-8-78 (1 page)
GL1200
Special Consumer Report: 1984 and 1985 GW Rear Hub
New media
New comments
Search media
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
General Discussion
General Chit-Chat
found a new project for my wing.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support Classic Goldwings:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="Goldtop" data-source="post: 206279" data-attributes="member: 5268"><p>ok. top bracket attached. I broke my rules sort of straight away. I've removed the capture bolts that used to hold the top of the mesh screen. one broke in half when I removed the bolt. </p><p>I've decided to bend over the top bracket so it will attach to the top of the new cover. unfortunately I've had to drill two new holes in the rad cover. to accept the original holes in the top mount plate.</p><p>in removing the very rusty wire mesh I've found one of the bottom rad bolts has rusted clean through. I now have to resecure the bottom of the rad. </p><p>my remaining mounting points are on the side of the rad cover, no where near any original mount point. </p><p>I have spotted a mount point on the engine bars that will work.</p><p>it's ridged and I can fabricate a bracket to join this point to the rad cover. </p><p>I need to paint the brackets but I'll take some pictures of the new mounting points bedorehand and post them tomorrow or the day after. I'll also post some close ups of the rad cover in position.</p><p>with all the broken bolts and mounts I can now see why the old one needed to go. </p><p>see you all soon.</p><p></p><p></p><p>Sent from my SM-G920F using Tapatalk</p></blockquote><p></p>
[QUOTE="Goldtop, post: 206279, member: 5268"] ok. top bracket attached. I broke my rules sort of straight away. I've removed the capture bolts that used to hold the top of the mesh screen. one broke in half when I removed the bolt. I've decided to bend over the top bracket so it will attach to the top of the new cover. unfortunately I've had to drill two new holes in the rad cover. to accept the original holes in the top mount plate. in removing the very rusty wire mesh I've found one of the bottom rad bolts has rusted clean through. I now have to resecure the bottom of the rad. my remaining mounting points are on the side of the rad cover, no where near any original mount point. I have spotted a mount point on the engine bars that will work. it's ridged and I can fabricate a bracket to join this point to the rad cover. I need to paint the brackets but I'll take some pictures of the new mounting points bedorehand and post them tomorrow or the day after. I'll also post some close ups of the rad cover in position. with all the broken bolts and mounts I can now see why the old one needed to go. see you all soon. Sent from my SM-G920F using Tapatalk [/QUOTE]
Insert quotes…
Verification
Post reply
General Discussion
General Chit-Chat
found a new project for my wing.
Top